manualshive.com logo in svg

Siemens MOTOX BA 2010, Operating Instructions Manual, Page: 53 / 124

Share
Download
Siemens MOTOX BA 2010 Operating Instructions Manual Download Page 53

 

BA 2010 
Operating Instructions, 02/2018, A5E38093846A/RS-AC 

51

 

 

Operation 

6 

 

 

 

 

ATEX version gearboxes 
The difference between the temperature of the housing and the ambient 

temperature of max. +40° C must not exceed 70 K. 
Using a suitable temperature sensor, measure the temperature at the lowest point 

of the housing (oil sump) or at the mounting surface in the case of output units. 
Changes are an indication of possible incipient damage. 

 

 

 

CAUTION 

Malfunctions can cause personal injuries or gearbox damage 
In the event of changes during operation, the drive unit must be switched off immediately. 
Determine the cause of the fault using the fault table (Page 53). Remedy faults or have 

faults remedied. 

 

Check the gear unit during operation for: 

●

 

Excessive operating temperature 

●

 

Changes in gear noise 

●

 

Possible oil leakage at the housing and shaft seals 

Summary of Contents for MOTOX BA 2010





























































































































Reviews:

No comments