Siemens MOTOX BA 2010 Operating Instructions Manual Download Page 49

Page: 49 / 124

Installation

4.10 Removing and installing the shaft-mounted gearbox

BA 2010
Operating Instructions, 02/2018, A5E38093846A/RS-AC

4.10.4.2

Mounting torque arms on parallel shaft gearboxes

We recommend using pretensioned, damping rubber elements.
Fixing accessories such as angles, bolts, nuts, etc., are not included in the scope of delivery.

Figure 4-11 Mounting suggestion for torque arm on F.28, 38B - 188B

Size

38B

48B

68B

88B

108B 128B 148B 168B 188B

x [mm]

13.1

18.2

27.2

35.8

34.8

46.2

45.1

Size 208

Note
The torque arm bush must be supported by bearings on both sides.

Figure 4-12 Mounting suggestion for torque arms on F.208

Procedure

Clean the contact surfaces between the housing and the torque arm.

Tighten the M30 bolts, strength class 8.8, with 1 500 Nm tightening torque.

You have now mounted the torque arm.

Summary of Contents for MOTOX BA 2010





























































































































Search results

Summary of Contents for MOTOX BA 2010

Reviews:

Siemens MOTOX BA 2010, Operating Instructions Manual, Page: 49 / 124

Search results

Summary of Contents for MOTOX BA 2010

Reviews: