manualshive.com logo in svg

Siemens MD-P1, User Manual, Page: 5 / 76

Share
Download
Siemens MD-P1 User Manual Download Page 5

Introduction 

 

Product Description 

 

5 

Siemens Industry, Inc. 

 

125-201 

 

 

09/30/2019 

 

Introduction 

Product Description 

The MD-P1 and MD-P1D Power Meters monitor the voltage, current, power, energy 
and many other electrical parameters on single and three-phase electrical systems. 
The meters use direct connections to each phase of the voltage, and use current 
transformers to monitor each phase of the current. Information on energy use, 
demand, power factor, line frequency and more are derived from the voltage and 
current inputs. 

The communications interface to the meters is an RS-485 serial connection that uses 
the Siemens P1 FLN protocol for sending commands and retrieving data. An APOGEE 
Building Management and Control System is usually connected to the MD-P1 or MD-
P1D Power Meter. This APOGEE system unit provides data recording and trend 
logging plus a human interface or display. 

Up to 20 MD-P1 or MD-P1D Power Meters may be connected to a single P1 network 
for monitoring and recording power usage at multiple locations within a single site.  

The MD-P1D Meter, with an integral 2-line × 16 LCD display provides visual feedback 
of volts, amps, and Kw, (see Appendix C). 

 

Table 1: Product Numbers 

Product Number 

MD-P1, MD-P1D Power Meter Bundled Kit Descriptions 

MD-P1 Power Meter Bundled Kits; Standard Grade 

MD-P1-3-CTSC-100A 

Meter with three 100A, split-core current transformers with 1" windows 

MD-P1-3-CTSC-200A 

Meter with three 200A, split-core current transformers with 1" windows 

MD-P1-3-CTSC-400A 

Meter with three 400A, split-core current transformers with 1.25" windows 

MD-P1-3-CTSC-600A 

Meter with three 600A, split-core current transformers with 2" windows 

MD-P1-3-RC-16 

Meter with three 4000A, 

16” Rogowski Coil CTs, with 5" diameter windows 

MD-P1-3-RC-36 

Meter with three 4000A, 36” Rogowski Coil CTs with 10” diameter windows 

 

 

MD-P1D Power Meter Bundled Kits; Standard Grade with Display 

MD-P1D-3-CTSC-100A 

Meter with display, and three 100A, split-core current transformers with 1" windows 

MD-P1D-3-CTSC-200A 

Meter with display, and three 200A, split-core current transformers with 1" windows 

MD-P1D-3-CTSC-400A 

Meter with display, and three 400A, split-core current transformers with 1.25" windows 

MD-P1D-3-CTSC-600A 

Meter with display, and three 600A, split-core current transformers with 2" windows 

MD-P1D-3-RC-16 

Meter with display, and three 4000A, 16” Rogowski Coil CTs with 5” diameter windows 

MD-P1D-3-RC-36 

Meter with display, and three 4000

A, 36” Rogowski Coil CTs with 10” diameter windows 

 

Summary of Contents for MD-P1













































































Reviews:

No comments