manualshive.com logo in svg

Siemens MD-12HD, User Manual, Page: 64 / 74

Share
Download
Siemens MD-12HD User Manual Download Page 64

 

63 

Siemens Industry, Inc. 

Step 4) 

Putting it all together

 

VIA MODBUS RTU (SERIAL) USING FUNCTION CODE 6 / WRITE SINGLE REGISTER 

ID FC ADDR  DATA  CRC 

(note CRC order is swapped)

 

01 06 08 AA 

42 C8

 9A BC  

01 06 08 AB 

00 00 

FA 4A

 

 

VIA MODBUS RTU (SERIAL) USING FUNCTION CODE 16 / WRITE MULTIPLE REGISTER 

ID FC ADDR  #REGS  LN DATA0 DATA CRC 

01 10 08 AA 00 02 04 

42 C8 00 00

 8B EE 

 
 

VIA MODBUS TCP (ETHERNET) USING FUNCTION CODE 6 / WRITE SINGLE REGISTER 

TXNID PROID LENGT ID FC ADDR  DATA 

(TXNID will be arbitrary)

 

01 87 00 00 00 06 01 06 08 AA 

42 C8

 

01 88 00 00 00 06 01 06 08 AB 

00 00

 

 

VIA MODBUS TCP (ETHERNET) USING FUNCTION CODE 16 / WRITE MULTIPLE REGISTER 

TXNID PROID LENGT ID FC ADDR  #REGS LN DATA0 DATA1  

01 87 00 00 00 0B 01 10 08 AA 00 02 04 

42 C8 00 00 

 

Commands Requiring a Processor Reset 

Register manipulation of communication protocols or addressing require that the MD-xxHD perform a 
“soft reset” in order to take effect. Register 2100 can receive a user command to facilitate this process. 
BACnet users write a 

1

 and Modbus users write 

1234

 to effect a soft reset. The MD-xxHD reboot time is 

approximately 10 seconds. 

See the Modbus examples document on the DENT Instruments web site or included with your electronic 
documentation for additional support on programming Modbus. The following online resources are also 
helpful. 

http://Modbus.org/docs/PI_MBUS_300.pdf

 

http://www.Modbustools.com/Modbus.html 

http://www.simplyModbus.ca/TCP.htm 

http://www.tahapaksu.com/crc/

 

Windows Calculator (Programmer mode) 

 

 

Summary of Contents for MD-12HD











































































Reviews:

No comments