manualshive.com logo in svg

Siemens MD-12HD, User Manual, Page: 33 / 74

Share
Download
Siemens MD-12HD User Manual Download Page 33

 

Siemens Industry, inc. 

32 

MacOS Users 

ViewPoint HD is a Windows application and does not run on MAC OS. MAC users can, however, make 
use of the MD-xxHD Web App interface through the USB port by installing a CDC-EEM driver. This driver 
is available in the Media Distribution materials or can be downloaded from the DENT Instruments web 
site. 

 

 

 

 

1.  Users must have OS version of 10.11.1 or higher. 
2.  Drag the file dentinstruments-2.03a1.dmg onto the desktop. 
3.  Double-click the dmg file to initiate the MAC installer. 
4.  Follow the installation prompts. 
5.  Reboot the MAC after the installation process is complete. 
6.  Connect the MD-xxHD meter to the MAC with USB cable. 
7.  Open Safari browser and type IP address 169.254.1.5 to access the MD-xxHD Web App 
8.  If no login credentials are setup, click on 

LOGIN

 button with blank for password. 

9.  The MD-xxHD Web App checks for login credentials and, if passed, opens Real Time Web Page. 

 

 

 

Summary of Contents for MD-12HD











































































Reviews:

No comments