manualshive.com logo in svg

Siemens MD-12HD, User Manual, Page: 23 / 74

Share
Download
Siemens MD-12HD User Manual Download Page 23

 

Siemens Industry, inc. 

22 

Network Scan 

Network Scan is a feature for monitoring previously installed and configured MD-xxHD meters over an 
Ethernet network. Network Scan will broadcast a UDP discovery packet on the same network as the PC 
running the ViewPoint HD application. Normally this will be performed on a corporate network running 
DHCP. Any MD-xxHD meter that responds will be displayed in a table that includes the system 
description register, IP address, serial number, and communication configuration. 

 

Highlight the desired meter and select 

OK

, 

Test 

or 

Setup

. Note that the effectiveness of this technique is 

highly dependent on the configuration of the PC running ViewPoint HD (which may have more than one 
network card) and the network configuration. Rescans can be used to make multiple attempts to locate a 
particular meter on busy networks (UDP has no built-in retry provisions). 

Launch Configurator 

The final option in the ViewPoint HD Connect to Meter pop-up window is 

Launch Configurator

. This 

option allows for the creation of a meter setup or alarm table for future use without connecting to a meter. 
After prompting the user for a meter model (shown below), ViewPoint HD launches under a mode with 
restricted functionality. This mode operates on files only. 

 

 

Summary of Contents for MD-12HD











































































Reviews:

No comments