Siemens MD-12HD User Manual Download Page 15

Page: 15 / 74

Siemens Industry, inc.

Meter Configuration Overview

▪

Work performed ahead of the installation saves time in the field and results in fewer
mistakes!

Tools

Typical Work

•

Desktop or Laptop PC

•

USB Type AB Cable (preferred) or

Ethernet and USB wall charger
(> 500 mA)

•

Thumb Drive included with order

(ViewPoint HD Installer) or access to

https://www.dentinstruments.com/siemens

•

Electrical Schematics of project

•

Installation of ViewPoint HD Software

•

Connect USB/Ethernet cable from PC

to meter

•

Establish communication with meter

•

Firmware update (if desired)

•

Configure software for anticipated

meter setup

•

Field wiring documentation

•

Set alarms

•

Set security PINs

Meter Installation Overview

▪

Performed by licensed electrician.

Tools

Typical Work

•

Mounting hardware (customer

supplied)

•

Wiring and supplies, labels, wire ties

•

Tablet, Smart Device, or

Laptop PC

•

Multi Meter, Current Clamp

•

Camera

•

Mechanical mounting

•

Electrical installation

•

Install voltage cover

•

Apply power to meter

•

Confirm basic operation of meter

Summary of Contents for MD-12HD











































































Search results

Summary of Contents for MD-12HD

Reviews:

Siemens MD-12HD, User Manual, Page: 15 / 74

Search results

Summary of Contents for MD-12HD

Reviews: