manualshive.com logo in svg

Siemens MAGNETOM Skyra, Owner'S Manual, Page: 121 / 124

Share
Download
Siemens MAGNETOM Skyra Owner'S Manual Download Page 121

Operator Responsibilities for Maintenance

13

© Siemens, 2009

M7-000.664.01.04.02

Page 13 of 14

MAGNETOM 

03.12

CS SD MR

  

Tim dockable table

Preventive measure to 
avoid wear and tear

Check the docking mechanism

Check the hydraulic system

Check/refill hydraulic oil

Check/clean connectors of the docking 
station

Lubricate RF connectors

Annually

RF connectors

Preventive measure to 
avoid wear and tear

Check/clean connectors

Lubricate RF connectors

Annually

Comfort kit (option)

Preventive measure to 
avoid overheating

Replace air filter

Every 
2 years

Software Preventive 

measure 

against data loss in the 
case of hard disk failure

Save dynamic data

Clean up directories

Every 
3 months

1. According to manufacturer recommendations

2. According to manufacturer recommendations

3. Zero helium boil off rate for typical clinical use, depending on sequence and operating time with running helium compressor. 

The system needs to be serviced at regular intervals. Undisturbed magnet cooling for 24 hours and 7 days a week.

4. If the system is not connected to Siemens Remote Service (SRS) the replacement has to be performed according to manu-

facturer recommendations. The replacement is performed “on demand” when the system is connected to Siemens Remote 
Service (SRS). 

Object or function

Reason

What is checked:

Interval

Summary of Contents for MAGNETOM Skyra





























































































































Reviews:

No comments