manualshive.com logo in svg

Siemens MAGNETOM Skyra fit, Operator'S Manual, Page: 45 / 131

Share
Download
Siemens MAGNETOM Skyra fit Operator'S Manual Download Page 45

CAUTION

Squeeze bulb is defective!

Risk of injury to patient because emergencies cannot be
communicated

◆

Check the functionality of the squeeze bulb daily.

Coolant accidents

During a quench, a person might become unconscious due to severe
shortness of breath:

1

Remove unconscious persons immediately from the examination
room.

2

Start adequate first aid measures and contact a physician
immediately.

Direct contact with subzero liquids, gases, and surfaces (e.g. pipes)
may lead to frostbite. The eyes and mucous membranes are
especially vulnerable.

CAUTION

Improper handling of liquid helium!

Skin damage caused by frostbite

◆

Do not rub frostbitten skin areas.

1

Remove clothing carefully from the locations involved.

2

Rinse frostbitten skin with lukewarm water.

3

Cover frostbitten skin with sterile bandages.

4

Do not apply powder or creams.

5

Contact a physician immediately.

2.4.3

First aid in case of shortness of

breath

First aid in case of frostbite

Safety

2

MAGNETOM Skyra

fit

 | syngo MR E11

45

Print No. M6-04401.621.02.02.02

Summary of Contents for MAGNETOM Skyra fit




































































































































Reviews:

No comments