manualshive.com logo in svg

Siemens MAGNETOM Skyra fit, Operator'S Manual, Page: 37 / 131

Share
Download
Siemens MAGNETOM Skyra fit Operator'S Manual Download Page 37

WARNING

When using the DIXON method, water and fat swaps might
occur!

Incorrect diagnosis

◆

Diagnosis should be confirmed by a second contrast and/or a
different orientation.

CAUTION

Poor image quality! Wrong image position!

Incorrect diagnosis

◆

Prior to the examination, inform patients about movements
and their negative effects on the measurement.

◆

Ensure that the patient does not move during the
measurement.

◆

Monitor the patient during the MR examination.

CAUTION

Imprecise localization due to patient movement during
functional MR imaging (fMRI)!

Incorrect stereotactic planning and injury of the patient

Incorrect assignment of active brain areas

◆

Prior to the examination, inform patients about movements
and their negative effects on the measurement.

◆

Use Siemens scan protocols with motion correction.

◆

Monitor the patient to ensure that the task is performed
correctly.

DIXON swapping

Patient-related artifacts/

imaging errors

Safety

2

MAGNETOM Skyra

fit

 | syngo MR E11

37

Print No. M6-04401.621.02.02.02

Summary of Contents for MAGNETOM Skyra fit




































































































































Reviews:

No comments