manualshive.com logo in svg

Siemens MAGNETOM Skyra fit, Operator'S Manual, Page: 34 / 131

Share
Download
Siemens MAGNETOM Skyra fit Operator'S Manual Download Page 34

Causes

: Artifacts and imaging errors are listed according to their

source for error:

◾

System-related artifacts/imaging errors

◾

Patient-related artifacts/imaging errors

◾

User-related artifacts/imaging errors, see: 

Software operator

manual

User-related and patient-related artifacts/imaging errors can be
largely avoided through patient instructions and proper conduct of
patient and personnel.

The MR image may show system-related artifacts/imaging errors
despite careful preparation.

◆

If the same artifact/imaging error appears repeatedly, document
and submit it to Siemens Service.

CAUTION

RF-signal interference caused by incompatible accessories e.g.
patient monitoring devices!

Streaks and bright spots in the MR image

◆

Use only accessories tested and approved for the MR system.

◆

Keep the door to the examination room closed.

◆

Vary the bandwidth of the MR sequence.

◆

Whenever possible, use local coils for the MR examination.

CAUTION

Phasing of MR signal is not set correctly!

Structure is shown in the wrong position

◆

Repeat the measurement for the structure in question by
using a second orthogonal slice and check whether the
position of the structure is reproducible nor not.

System-related artifacts/

imaging errors

Stripe artifacts

Incorrect slice positioning

2

Safety

34

MR System | Operator Manual

Print No. M6-04401.621.02.02.02

Summary of Contents for MAGNETOM Skyra fit




































































































































Reviews:

No comments