Siemens M20 Terminal Technical Description Download Page 91

Page: 91 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

AT+VGT

Transmit gain selection of microphone

Test command

AT+VGT=?

Response

+VGT: (list of supported <n>) OK

Parameter

see set command

Read command

AT+VGT?

Response

+VGT: <n> OK

Note

this command may only be used with (AT^SNFS=3) audio mode 3.

Parameter

see set command

Set command

AT+VGT=[<n>]

Response

TA sets amplification of audio samples sent from the TA to the computer.

Parameter:

<n>

0 – Automatic gain control

1(0x1)-128(0x80)-255(0xFF)

gain=20*log(n/128)

Note

default value is 128.

Hex input not accepted

Reference

GSM 07.07

Note

Set command works only in audio mode 3.

AT+VIP

Initialize voice parameters

Test command

AT+VIP=?

Response

+VIP: list of supported <n>s OK

Parameter

see set command

Test command

AT+VIP?

Response

+VIP: <n> OK

Parameter

see set command

Set command

AT+VIP=<n>

Response

TA activates the selected audio set.

Parameter

<n>

1(0x1)

Audio mode 1: standard mode approved for handset V38140-H-X33

3(0x3)

Audio mode 3: customer-specific mode; all audio parameters can be
adjusted by AT commands

Reference

GSM 07.07

Note

In mode 1, no audio parameters can be set. The following set commands can be used in mode 3:

+VGR

+VGT

^SNFA

^SNFI

^SNFO

^SNFE

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands