Siemens M20 Terminal Technical Description Download Page 86

Page: 86 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

AT+CSCS

Select TE character set.

Test command

AT+CSCS=?

Response

+CSCS: list of supprted <chset>s

Parameter

see set command

Read command

AT+CSCS?

Response

TA returns current setting of conversion scheme.

+CSCS: <chset>

Parameter

see set command

Set command

AT+CSCS=<ch-
set>

Response

Set command informs TA which character set

<chset>

is used by the TE. TA is then able to con-

vert character strings correctly between TE and ME character sets.

Parameter

<chset>

conversion schemes

"IRA"

international reference alphabet (ITU-T T.50)

"PCCP850"

MS-DOS Code Page 850 - Latin 1

"PCCP852"

MS-DOS Code Page 852 - Latin 2

"PCCP1252"

Code Page 1252 Windows Latin 1 (ANSI)

"PCCP1250"

Code Page 1250 Windows Latin 2 (Central Europe)

"8859-

ISO 8859 Latin 1 character set

"8859-

ISO 8859 Latin 2 character set

"TTP"

GSM default alphabet (GSM 03.38 subclause 6.2.1); except the values 0 to 32 are mapped

to 128. This setting does not cause problems with software flow control (XON/XOFF).

Reference

GSM 07.07

Note

When TA-TE interface is set to 8-bit operation and used TE alphabet is 7-bit, the highest bit will
be set to zero.

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands