Siemens M20 Terminal Technical Description Download Page 79

Page: 79 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

AT+CPWD

Change password

Test command

AT+CPWD=?

Response

TA returns a list of pairs which present the available facilities and the maximum length of their
password.

+CPWD: list of supported (<fac>, <pwdlength>)s OK

Parameter

<fac>

see execute command

<pwdlength>

integer max. length of password

Execute command

AT+CPWD =
<fac>, [<oldpwd>],
<newpwd>

Response

TA sets a new password for the facility lock function.

If error is related to ME functionality:

+CME ERROR: <err>

Parameter

<fac>

"SC" SIM (lock SIM card) (SIM asks password in ME power-up and when this lock

command issued)

"AO" BAOC (Bar All Outgoing Calls)

"OI"

BOIC (Bar Outgoing International Calls)

"OX" BOIC-exHC (Bar Outgoing International Calls except to Home Country)

"AI"

BAIC (Bar All Incoming Calls)

"IR"

BIC-Roam (Bar Incoming Calls when Roaming outside the home country)

"AB" All Barring services (applicable only for <mode>=0)

"AG" All outGoing barring services (applicable only for <mode>=0)

"AC" All inComing barring services (applicable only for <mode>=0)

"P2"

SIM PIN2

<oldpwd>

password specified for the facility from the user interface or with command. If an old
password has not yet been set, <oldpwd> is not to be entered.

if <fac> = "SC" then PIN

if <fac> = "AO"..."AC" (Barring) then network password

if <fac> = "P2" then PIN2

Note:

a password may already be set, depending on the provider. Please check with
your provider.

<newpwd>

new password

Reference

GSM 07.07

Note

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands