Siemens M20 Terminal Technical Description Download Page 77 | Manualshive

Page: 77 / 234

background image

AT command interface

Version 8 dated 15.03.00

77

Siemens Information and Communication Products

AT+CPIN

Enter PIN

Test command

AT+CPIN=?

Response

OK

Read command

AT+CPIN?

Response

TA returns an alphanumeric string indicating whether some password is required or not.

+CPIN: <code> OK

If error is related to ME functionality:

+CME ERROR: <err>

Parameter

<code>

READY

no further entry needed

SIM PIN

ME is waiting for SIM PIN

SIM PUK

ME is waiting for SIM PUK

PH_SIM PIN

ME is waiting for phone to SIM card (antitheft)

SIM PIN2

PIN2, e.g. for editing the FDN book possible only
if preceding command was acknowledged with
+CME ERROR:17

SIM PUK2

possible only if preceding command was acknowledged
with error +CME ERROR:18.

Set command

AT+CPIN=<pin>

[, <new pin>]

Response

TA stores a password which is necessary before it can be operated (SIM PIN, SIM PUK, PH-SIM
PIN, etc.). If the PIN is to be entered twice, the TA shall automatically repeat the PIN. If no PIN
request is pending, no action is taken and an error message, +CME ERROR, is returned to TE.

If the PIN required is SIM PUK or SIM PUK2, the second pin is required. This second pin, <ne-
wpin>, is used to replace the old pin in the SIM.

OK

If error is related to ME functionality:

+CME ERROR: <err>

Parameter

<pin>

password (string type) should be entered in double quotes.

E.g.: AT+CPIN=”9515”

<new pin>

if the PIN required is SIM PUK or SIM PUK2: new password

Reference

GSM 07.07

Note

1. <pin> and <new pin> must be entered with double quotes (i.e. “1234“)

2. Wait 10 sec after PIN input before using SMS related commands.

«
...
75
76
77
78
79
...
»

Summary of Contents for M20 Terminal











































































































































































































































Reviews:

No comments

Related manuals for M20 Terminal

Brand: O.S. engine Pages: 5

MAX-15CV-R Series

Brand: O.S. engine Pages: 19

Brand: Nanni Pages: 24

Brand: Evinrude & Johnson Pages: 349

Brand: Briggs & Stratton Pages: 20

Rotax 125 JUNIOR MAX evo

Brand: BRP Pages: 174

EVINRUDE E-TEC BE225HGXABA

Brand: BRP Pages: 356

Brand: Arrow Shark Pages: 16

Brand: Volvo Penta Pages: 44

Brand: Volvo Penta Pages: 52

Brand: Volvo Penta Pages: 74

Brand: Volvo Penta Pages: 88

Brand: Lombardini Pages: 64

11LD522-3 Series

Brand: Lombardini Pages: 44

Brand: Lombardini Pages: 58

Brand: Lombardini Pages: 68

Brand: Lombardini Pages: 109

Brand: CW Products Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands