manualshive.com logo in svg

Siemens M20 Terminal, Technical Description

Share
Download
Siemens M20 Terminal Technical Description Download Page 61

AT command interface

Version 8 dated 15.03.00

61

Siemens Information and Communication Products

A

AT+CCUG

Closed user group control

Test command

AT+CCUG=?

Response

OK

Parameter

Read command

AT+CCUG?

Response

+CCUG: <n>,<index>,<info> OK

If error is related to ME functionality:

+CME ERROR: <err>

Parameter

see set command

Set command

AT+CCUG=[<n>] 
[,<index>[,<in-
fo>]]]

Response

TA sets the closed user group supplementary service parameters as a default adjustment for all fol-
lowing calls.

OK

Parameter

<n>

0

disable CUG

1

enable CUG

<index>

0...9

CUG index

10

no index (preferred CUG taken from subscriber data)

<info>

0

no information

1

suppress OA (Outgoing Access)

2

suppress preferential CUG

3

suppress OA and preferential CUG

Reference

GSM 07.07

Note

Summary of Contents for M20 Terminal











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands