Siemens M20 Terminal Technical Description Download Page 39

Page: 39 / 234

AT command interface

Version 8 dated 15.03.00

Siemens Information and Communication Products

ATI

Display product identification information

Execute command

ATI

Response

ME issues product information text

SIEMENS

M20

Revision: x.yy, DD.MM.YY HH:MM

Explanation of "Revision" parameter:

Version (x) and variant (y) of software release.

Date and time of software production

DD: day, MM: month, YY: year, HH: hours, MM: minutes

Parameter

Reference

V.25ter

Note

Same response for ATI1...ATI9

ATO

Switch from command mode to data mode

Execute command

ATO[n]

Response

TA resumes the connection and switches back from command mode to data mode.

If connection is not successfully resumed

NO CARRIER

TA returns to data mode from command mode CONNECT <text>

Note:

<text> only if parameter

setting X>0

Parameter

<n>

switch from command mode to data mode

Reference

V.25ter

Note

ATQ

Set result code presentation mode

Set command

ATQ[<n>]

Response

This parameter setting determines whether or not the TA transmits any result code to the TE. Infor-
mation text transmitted in response is not affected by this setting.

If <n>=0:

If <n>=1:

(none)

Parameter

<n>

DCE transmits result code

Result codes are suppressed and not transmitted

Reference

V.25ter

Note

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Brands by name

Popular brands