Siemens M20 Terminal Technical Description Download Page 177

Page: 177 / 234

Application notes

Version 8 dated 15.03.00

177

Siemens Information and Communication Products

8.3.3

SW download

8.4

Serial interface configuration

The serial interface to the M20/M20 Terminal has to be initialized as follows:

19200,8,N,1 (baud rate 19200, data bits: 8, parity: no, stop bit: 1)

A serial interface configuration file for a Windows 95/98/NT Hyperterminal program (file: m20.ht) can be found on the

+CLCK: 1,4 /
Outgoing fax call
barred

AT+CLCK="AO",0,"<c
ode>",7 /Unlock all
services, <code> availa-
ble from
Network provider
(barring services)

No VOICE
call
possible

No Carrier

M20 active, boo-
ked into net (M20
idle), VOICE
number exists
M20T LED ON

ATD<num>
; Semicolon
is last cha-
racter!
Otherwise
DATA call

Check if <num> exists,
<num> has to
include AREA CODE

No DATA
call
possible

No Carrier

M20 active, boo-
ked into net (M20
idle), DATA
number exists
M20T LED ON

SIM card must have activated
DATA number

SIM card DATA number
available from Network
provider

ATD<num>
NO Semico-
lon as last
character!
Otherwise
VOICE call

SIM card must have acti-
vated DATA number

No FAX call
possible

No Carrier

M20 active, boo-
ked into net (M20
idle), FAX num-
ber exists M20T
LED ON

SIM card must have activated
FAX number

SIM card must have acti-
vated FAX number

Distorted or no speech from
the far end during an active
call

M20: microphone externally biased and not DCde-
coupled from M20

Couple microphone li-
nes to M20 with
capacitors, Bias micro-
phone balanced to GND

Fault

Error
Message

Status

Check

SW response /
comment

Action

No SW download after power
up

M20T: LED on/
blinking

Bootcode enable must be high
during power up

Bootcode enable must
be high together with po-
wer on and needs to
remain high for at least 1
second. If initialisation
correct; M20T LED
stays dark after power on

Ignition must be set high during
complete download

Ignition must be set high
during complete down-
load

M20T: LED Off,
power is on

PCload32.exe does no download See chapter on SW

download

Summary of Contents for M20 Terminal











































































































































































































































Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands

Siemens M20 Terminal, Technical Description

Search results

Summary of Contents for M20 Terminal

Reviews:

Related manuals for M20 Terminal

Brands by name

Popular brands