52,4
90
1
1
1
71,5
P1
P2
P3
2
P1
AC/DC
230V
P2 P3 P4
L1 N
X1:P4
X1:P1
X1:P2
X1:P3
X10
1
1
3
6GK7177-1FA10-0AA0
s
LOGO! CSM230
DC 115...210V 0.02...0.01A
AC 100...240V ~ 0.02...0.01A
X1:P1 TO X1:P4 FOR LAN ONLY
Mounting slides
Hole pattern for wall mounting
Prior to wall-mounting, the mounting slides on the back
of the device are pushed open.
98 +/- 0.3
1
2
P1
AC/DC
230V
P2 P3 P4
X1:P4
X1:P1
X1:P2
X1:P3
L- N
36.0
cULus
C-Tick
- UL 508 Listed
- CSA C22.2 Number 142
AS/NZS 2064 Class A
cULus Haz.Loc.
FM
You can use the device in the following hazardous locations:
IND. CONT. EQ., E223122, UL 1604, UL 2279-15
FM3600 and 3611:
CL. I, Div. 2, Group A, B, C, D, T4
CL. I, Zone 2, Group IIC, T4, Ta = 55°C
Installation, Connection, Technical specifications
2
3
1
EU Directive 2004/108/EC "Electromagnetic Compatibility" (EMC Directive)
-
Emission: EN 55022 Class B: 2010
-
Immunity: EN 61000-6-2: 2005
EU Directive 2006/95/EC "Low Voltage Directive" (LVD)
- Safety: EN 61131-2: 2008
The EC Declaration of Conformity is available for all responsible authorities at:
Siemens Aktiengesellschaft
Industry Automation, I IA SC CI
Postfach 4848
D-90026 Nuernberg
Germany
You will find the EC Declaration of Conformity for this product on the Internet
at the following address:
http://support.automation.siemens.com/WW/view/en/10805878
→ Tab "Entry List"
Filter settings: Entry type: "Certificates"
Certificate Type: "Declaration of Conformity"
Search items(s): <name of the module>
The product meets the requirements and aims of the following EC directives:
Sources of information and other documentation
The "SIMATIC NET Industrial Ethernet Network Manual" contains
detailed information on the network structure, maximum cable lengths,
cabling technology etc.
http://support.automation.siemens.com/WW/view/en/
27069465
Entry ID: 27069465
You will find additional information on the Siemens LOGO! Web page:
http://www.siemens.com/logo
Neutral Conductor
N
Conductor
L1
Functional grounding
RJ-45 jacks for connections via Ethernet (10/100 Mbps)
LED for the power supply (AC/DC 230V) and
LEDs for the Ethernet communication status (P1 - P4)
Three screw terminals:
AC 47... 63 Hz
Permitted line power frequency
Technical specifications
All ports adhere to 1.5 kV insulation voltage:
- to shield
- between the ports.
Insulation of the ports
Ethernet interface
300 seconds
Aging Time
1024
Functional grounding can be established by connecting a cable
from terminal 3, for example to the DIN rail. Such a cable should be
kept as short as possible. Grounding is, however, not necessary for
interference-free operation.
Functional grounding
Per terminal for L1 and N
Cable cross section: 1 x 2.5 mm2 or 2 x 1.5 mm2
Connection
1.8 W
Effective power loss
- AC 100 ... 240 V: 0.05 ... 0.03 A
- DC 115 ... 210 V: 0.02 ... 0.012 A
Current consumption (I)
AC 100 ... 240 V
DC 115 ... 210 V
Input voltage
Electrical specification
Delay resulting from latency
64 byte
Smallest data packet
1518 byte
Largest data packet
A standard Ethernet cable can be connected to the Ethernet interface.
However, to minimize electromagnetic interference, Siemens
recommends a shielded Ethernet cable with a twisted pair
(category 5) with a shielded RJ-45 connector at both ends.
Network cable
4 x RJ‑45 jacks with MDI‑X assignment 10/100 Mbps
(half / full duplex), autopolarity, autonegotiation
Communications connector
Star and bus topology
Note that the direct connection of two ports on the switch or
accidental connection over several switches causes an illegal loop.
Such a loop can lead to network overload and network failures.
Topology
When a frame passes through the CSM 230, it is delayed
by the store and forward function of the switch:
- with a 64 byte frame length by approx. 8 μs (at 100 Mbps).
- with a 1518 byte frame length by approx. 125 μs (at 100 Mbps).
Technical specifications
You will find the currently valid approvals on the type plate.
Approvals
http://www.siemens.com/logo
When installing and connecting up, keep to the procedures described in the LOGO! manual.
You will find additional information on the Siemens LOGO! web page:
Entry ID: 50074616
http://support.automation.siemens.com/WW/view/en/50074616
Entry ID: 27069465
http://support.automation.siemens.com/WW/view/en/27069465
Sources of information and other documentation
Prior to installation, connecting up and commissioning, read the relevant sections
in the LOGO! manual:
Installation
Order number: 6GK7177-1FA10-0AA0
Status of LEDs
Product information
© Siemens AG 2012
A5E03733191-04
CSM 230
LOGO!
Meaning
Status
LED
P1 - P4
P1 - P4
LOGO! receives / sends data via Ethernet.
Power is connected.
The connection via Ethernet is established (link up).
No connection via Ethernet (link down).
Power is not connected or the connected
power is too low.
Off
Off
Flashing
On
On
AC/DC
230V
AC/DC
230V
P1 - P4
IP 20
Degree of protection
35 mm DIN rail (DIN EN 60715 TH35) or wall mounting
Installation
Net weight
155 g
72 (4 TE) x 90 x 55 mm
Dimensions (W x H x D) in mm
< 90% (no condensation)
Relative humidity during operation
- 40°C … +70°C
Transport/storage temperature
0 … 55°C
Operating temperature
Further technical specifications
Learnable MAC addresses
DIN rail mount
2. Press down the lower part until the device locks in place.
The mounting slide on the back must snap into place.
1. Fit the LOGO! onto the DIN rail.
Pin 8 - n. c.
Pin 7 - n. c.
Pin 6 - TD -
Pin 5 - n. c.
Pin 4 - n. c.
Pin 3 - TD +
Pin 2 - RD -
Pin 1 - RD +
RJ-45 jacks with MDI-X assignment
Wall mounting
All dimensions in mm
Tightening torque 0.8 ... 1.2 Nm
Hole for screw Ø 4 mm
The "SIMATIC NET Industrial Ethernet Networking Manual" contains detailed information
on the network structure, maximum cable lengths, cabling technology etc.
To fulfill the requirements according radiated emission EN 55022 Class B, the shield of all
connected LAN cables must be grounded.
Release 06/2012
