Siemens LOGO! CIM Operating Manual Download Page 62

Page: 62 / 91

Web-based configuration

5.4 Web pages

LOGO! CIM

Operating Manual, 10/2021, A5E51250518-AA

5.4.6.4

Modbus RTU

This page allows you enable, disable and set the Modbus RTU connection.
LOGO! CIM supports only one Modbus RTU connection, either as Modbus RTU master or

Modbus RTU slave.

①

Enable or disable the Modbus RTU connection

Note: Modbus RTU connection is not secure.

②

Here you configure the properties of the connections of serial port.

•

Mode: RS485, RS422 or RS232

•

Baud-rate: set the transfer speed

•

Transmission: serial port setup

•

Terminal Resistor: enable or disable the embedded terminal resistor

③

Link to Modbus address space information page

④

Here you configure the Modbus RTU Type

•

If you select "Master", you need to set the "Data transfer table".

•

If you select "Slave", you need to set the "Modbus RTU Slave ID".
Range for the "Modbus RTU Slave ID": 1 to 255.

Summary of Contents for LOGO! CIM




























































































Search results

Summary of Contents for LOGO! CIM

Reviews:

Related manuals for LOGO! CIM

Brands by name

Popular brands

Siemens LOGO! CIM, Operating Manual

Search results

Summary of Contents for LOGO! CIM

Reviews:

Related manuals for LOGO! CIM

Brands by name

Popular brands