background image

2/17 

Building Technologies 

 

CC1N7106en 

HVAC Products 

 

20.02.2008 

Warning notes 

To avoid injury to persons, damage to property or the environment, the following 
warning notes must be observed! 
 
Do not to open, interfere with or modify the unit! 

 

 

All activities (mounting, installation and service work, etc.) must be performed by quali-
fied staff 

 

Before making any wiring changes in the connection area of the LME39…, completely 
isolate the plant from mains supply (all-polar disconnection). Ensure that the plant 
cannot be inadvertently switched on again and that it is indeed dead. If not discon-
nected, there is a risk of electric shock hazard 

 

Ensure protection against electric shock hazard by providing adequate protection for 
the burner control’s connection terminals 

 

Check the connecting lines of the air pressure switch for short-circuits («LP» between 
terminals 2 and 6) 

 

Press the lockout reset button / operation button only manually (applying a force of no 
more than 10 N) without using any tools or pointed objects 

 

Fall or shock can adversely affect the safety functions. Such units must not be put into 
operation, even if they do not exhibit any damage 

 

Each time work has been carried out (mounting, installation, service work, etc.), check 
to ensure that wiring is in an orderly state and make the safety checks as described in 
«Commissioning notes» 

 

The data line for the AZL2… display and operating unit or other accessories, such as 
the OCI410… (plugs into the BCI interface), must be connected or disconnected only 
when the burner control is dead (all-polar disconnection), since the BCI interface does 
not ensure safe separation from mains voltage 

Engineering notes 

 

When used in connection with actuators, there is no position feedback signal from the 
actuator to the burner control 

 

The running times of the actuators must match the burner control’s program. An addi-
tional safety check of the burner control together with the actuators is required 

 

If the communication interface (jack RJ11) is not used, protection against electric 
shock hazard must be provided (jack must be covered up) 

Mounting notes 

Ensure that the relevant national safety regulations are complied with. 

Summary of Contents for LME39 Series


















Reviews: