manualshive.com logo in svg

Siemens LITHOSTAR Multiline, Installation Instructions Manual, Page: 6 / 70

Share
Download
Siemens LITHOSTAR Multiline Installation Instructions Manual Download Page 6

LITHOSTAR Multiline

 

RXL2-120.812.01

Page 2 of 4

Siemens AG

System

Rev. 02

10.04

CS PS 24

Medical Solutions

1 - 2

General Remarks

 

Safety notes

1

•

The general safety notes for medical products must be observed in the performance of 
work and checks.

Yellow enameled Parts

1

•

All parts of the unit and of components that are painted with yellow/red enamel are 
shipping brackets which may be removed only in accordance with the Installation 
Instructions.

Test Equipment and Tools (Service Tools Cataloque)

1

Installation auxiliary devices

1

Materials

1

•

Tool kit for Installation engineers

•

Torque wrench (20 to 100 Nm)

•

Digital Multimeter 

Transport carriage roller set 

11 53 654 G5338
The roller set must be ordered if the system 
is not installed by the "Erlangen carrier".

•

Loctite 221

20 48 874 RV090

•

Oil for high voltage transformer H1 
for refilling only, if required

99 00 952

Summary of Contents for LITHOSTAR Multiline







































































Reviews:

No comments