background image

 

 

Installation Instructions 

Document No. 570-114 

October 26, 2016 

 

LCM-OAVS Room Pressurization with, 
Two Venturi Air Valves (One Exhaust, 
One Supply) and HW Reheat (including 
BTU Compensation) 

 

 

Item No. 570-114 Rev. CA

 

Page 1 of 8 

 

Generic Controller I/O Layout. See 

Wiring Diagram

 for application specific details. 

 

Control Applications 

6750, 6756 

Product Description 

The Siemens Venturi Air Valve is a pre-packaged, 

easy to install airflow measurement and control 

solution. It provides stable and precise airflow 

control of room supply, room general exhaust or 

fume hood exhaust. 
These instructions explain how to field install or 

replace the BACnet Laboratory Controller Module 

LCM. 
This BACnet LCM-OAVS VAV Room Pressurization 

Controller with HW Reheat and Two Fast-acting 

Venturi Air Valves — One Exhaust, One Supply 

features VAV control of a laboratory room with one 

supply duct, one exhaust duct, and up to six Fume 

Hoods. It uses fast-acting electronic actuators 

(shipped separately) to control the supply and 

exhaust Venturi air valves.  

This controller is built on a BACnet Programmable 

TEC (PTEC) platform that supports up to two 

Offboard AVS signals; however, Onboard AVS 

transducers are not supported. Offboard Air 

Module(s) (OAM) house AVS transducers and send 

signals to the AVS input(s) on the LCM OAVS 

board. 
The LCM can operate stand-alone, with a field 

panel, or as part of a network. 

Product Numbers 

See the 

Venturi Air Valve for Critical Environments 

Technical Specification Sheet

 (149-425) or 

Configuration and Sizing

 in the Critical Environments 

section of InfoLink. 

 

BACnet LCM-OAVS with HW Reheat 

and Two Venturi Air Valves — One 

Exhaust, One Supply Applications 6750 

(RTS) 6756 (BTU) 
This controller requires Offboard Air 

Module(s) (ordered and shipped 

separately 

570-804PA 

Summary of Contents for LCM-OAVS 570-804PA









Reviews: