background image

10

Prior to installation

Flat ducts 

must have an internal cross-

section that equates to that of round
pipes.

There should be no sharp bends.

For operating in exhaust-air mode, 

a

one-way flap should be mounted inside the
extractor hood unless there is already one
fitted in the outlet duct or wall ventilation
box.
If no one-way flap was enclosed with the
hood, it can be obtained from a specialist
retailer.

Installing the one-way flap:

For optimum extractor hood efficiency:

Short, smooth air exhaust pipe.

As few bends in the pipe as possible.

Diameter of pipe to be as large as
possible and no tight bends in pipe.

If long, rough exhaust-air pipes,
many pipe bends or smaller pipe 
diameters are used, the air extraction
rate will no longer be at an optimum
level and there will be an increase in
noise.

The manufacturer of the extractor

hoods accepts no liability for complaints
which can be attributed to the design
and layout of the pipework.

If pipes have different diameters:

Insert sealing strip.

For exhaust-air mode, 

ensure that

there is an adequate supply of fresh air.

Round pipes

Internal diameter

Flat ducts

Cross-section

l

100 mm

1

79 cm

2

l

120 mm

113 cm

2

l

150 mm

177 cm

2

Air connector 

l

150 mm

Mount the pipe
directly onto the air
outlet on the hood.

Attach the reducing
connector (enclosed
or available from
specialist retailer) 
to the air pipe and
then attach to the
exhaust-air duct.

Air connector 

l

120 mm

Mount the pipe
directly onto the air
outlet on the hood.

Attach the reducing
connector (enclosed
or available from
specialist retailer) 
to the air pipe and
then attach to the
exhaust-air duct.

Snap the one-way
flap into the air pipe.

The two lightly

sprung flaps must 
be able to move
upwards.

Summary of Contents for LC45 Series

















Reviews: