Siemens IM 153-4 PN Operating Instructions Manual Download Page 241

Page: 241 / 274

Technical Specifications

10.5 Response time of the ET 200M

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

239

10.5

Response time of the ET 200M

Response Time - A Definition

The response time is the time between detection of the input signal and the modification of

the associated output signal.

Duration

The response time depends on the bus structure and on the DP master / IO controller. Refer

to the DP master / IO controller manual for basics for calculating the response time.

Factors

The response time for the ET 200M depends on the following factors:
●

Processing the data through the ET 200M

●

Delay of the inputs and outputs (refer to the "S7-300 automation system, module

specifications (

http://support.automation.siemens.com/WW/view/en/8859629

)" reference

manual.

ET 200M

The time for processing the data within the ET 200M has a typical value of 1 ms. It is in this

time that the data processing takes place in the IM 153x and the data transfer between the

IM 153-x and the inserted modules.

3URFHVVLQJWKH
GDWDLQWKH
,0[

'DWDWUDQVIHU
EHWZHHQ
,0[DQG
PRGXOHV

'HOD\WLPHRIWKHLQSXWRXWSXW
PRGXOHV

UHIHUWRWKHUHIHUHQFHPDQXDO
IRUPRGXOHGDWD

Figure 10-6 Response time of the ET 200M

Summary of Contents for IM 153-4 PN



















































































































































































































































































Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands

Siemens IM 153-4 PN, Operating Instructions Manual

Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands