manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 236

Technical Specifications 

 

10.4 Technical specifications of the IM 153-4 PN interface module 

 

ET 200M 

234

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

10.4

 

Technical specifications of the IM 153-4 PN interface module 

Order Number    

6ES7153-4AA01-0XB0 

Properties   

The IM 153-4 PN interface module has the following properties: 
●

 

It interconnects the ET 200M with PROFINET IO. 

●

 

A maximum of 12 modules can be operated with the IM 153-4 PN 

●

 

It prepares the data for the inserted modules. 
The following settings can be made: SM, CP, non-assignable FM 

●

 

It supplies the backplane bus 

●

 

Integrated switch with 2 ports 

●

 

Transfer and backup of the device name on SIMATIC Micro Memory Card 

●

 

Firmware update using a SIMATIC Micro Memory Card or PROFINET IO 

●

 

The reference potential M of the rated supply voltage of the IM 153-4 PN to the rail 

(protective conductor) is connected by means of an RC combination, thus permitting an 

ungrounded configuration 

●

 

Supported Ethernet services 
–

 

ping 

–

 

arp 

–

 

Network diagnostics (SNMP): LLDP-MIB / MIB-2 

–

 

Resetting SNMP parameters to the factory settings 

–

 

I&M data 

●

 

Interrupts 
–

 

Diagnostic interrupts 

–

 

Hardware interrupts 

–

 

Removal / insertion interrupts 

–

 

Maintenance interrupts 

●

 

Port diagnostics 

●

 

Port disabling 

●

 

Support for real-time communication (RT Class 1 and Class 2). 

●

 

Maximum address space of 200 bytes I/O data. 

●

 

Data records for I/O modules 

●

 

As of 6ES7153-4AA01-0XB0: 
–

 

Isochronous real-time communication 

–

 

Minimum updating time 250 μs with IRT 

–

 

Prioritized startup 

–

 

Device replacement without removable media / programming device 

–

 

Changing IO devices during operation (changing partner ports) 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands