manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 190

Interrupt, error and system messages 

 

9.1 PROFIBUS DP 

 

ET 200M 

188

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

LEDs 

SF 

BF / 

BF1 

ACT 

ON 

Meaning 

Remedy 

flashes  flashes  flashes  flashe

s 

The IM 153-2 in the current operating 

mode is not compatible with the redundant 

IM 153-2. 

You will find information on 

compatibility between the versions of 

IM 153-2 in the chapter "Arrangement 

of the modules for the function "Change 

During Operation" and / or 

"Redundancy" (Page 44)" as well as in 

appendix "Compatibilities between the 

IM 153-x (Page 241)". 

*   not relevant 
**  After the transition to the redundant mode the SF LED flashes for a further 20 s. 

9.1.2

 

Diagnosis with STEP 7 or STEP 5 

Slave diagnosis 

The slave diagnosis behaves in accordance with the IEC 61784-1:2002 Ed1 CP 3/1 

standard. It can be read using 

STEP 7 or STEP 5 for all DP slaves (dependent on the DP 

master) which behave in accordance with the standard.  

Possibilities for reading the diagnosis 

Table 9- 3 

Reading the diagnosis with STEP 7 and STEP 5  

Automation system with 

DP master 

Block or tab in 

STEP 

7

 

Application 

See ... 

"DP slave diagnosis" 

tab 

Show slave diagnosis in clear 

text on the 

STEP 7

 interface 

"Diagnose hardware" in the online 

help for 

STEP 7

 

SFC 13 "DPNRM_DG" Read out slave diagnostics 

information (stored in the data 

area of the user program) 

SFC 59 "RD_REC" 

Read data records of the S7 

diagnosis (stored in the data 

area of the user program) 

Refer to chapter "Structure of the 

diagnostics (Page 191)" 

SFC refer to the reference manual 

"System and Standard Functions for 

S7-300/400 

(

http://support.automation.siemens.c

om/WW/view/en/1214574

)" 

FB 125 / FC 125 

Evaluate the slave diagnosis 

on the Internet 

(

http://support.automation.siemens.c

om/WW/view/en/387257

) 

SFB 52 

Read data record from the DP 

slave 

SIMATIC S7 / M7 

SFB 54 

Receive interrupts from the 

interrupt OBs 

STEP 7

 online help 

SIMATIC S5 with IM 308-C 

as DP master 

FB 192 "IM308C" 

SIMATIC S5 with S5 95U 

as a DP master 

FB 230 "S_DIAG" 

Reading out slave diagnostics 

information (storing in the data 

area of the user program) 
Note: not for enhanced 

diagnostics 

Refer to chapter "Structure of the 

slave diagnostics (Page 191)" 

FB refer to the "ET 200 Distributed 

I/O System 

(

http://support.automation.siemens.c

om/WW/view/en/1142470

)" manual 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands