Siemens IM 153-4 PN Operating Instructions Manual Download Page 17

Page: 17 / 274

Product overview

1.4 ET 200M distributed I/O device

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

"SIMATIC S7-DP-Slave"

The ET 200M distributed I/O system is a constituent part of the SIMATIC S7 automation

system.
In other words,

STEP 7 provides support when configuring, assigning parameters to and

programming the ET 200M in the DP master system as well as for the commissioning and

diagnostics. Special services and functions of the IM 153-2 (e.g. configurable FM) can be

used to their full extent only in the SIMATIC S7 / PCS 7.
If you use the ET 200M on a DP standard master (e.g. S5-95U), the configuration tool will

also provide support with the GSD file, but, for example, you must pay attention to the

technical data (project data) of the DP master (possible parameter assignment and

diagnostics message frame lengths etc.).
The PROFIBUS standard IEC 61784-1:2002 Ed1 CP 3/1 also includes the DPV1-mode. You

can use this mode only if you integrated the GSD-file Revision ≥ 3.

The GSD-file Revision 2 remains available and hence the compatibility with earlier versions

of the IM 153-x is assured.

Components

A series of components are provided for the configuration and commissioning of the ET

200M. The most important components and their functions are listed in the following table:

Table 1- 1

ET 200M components

Components

Function

Diagram

Mounting rail
Accessories:

•

Shield connecting element

... is the rack for the ET 200M.

Mounting Rail for Active Bus Module
Accessories:

•

Shield connecting element

•

active bus modules

... is the special rack for the ET 200M for

the functions "Module change during

operation", "Redundancy" and IM 153-4

PN.

Active bus modules (BM)

•

BM IM/IM for redundancy with 2 IM 153-2

•

BM IM/IM for redundancy with 2 IM 153-2Bx00

•

BM PS/IM for PS 307; 2 A and IM 153-x

•

BM 2 40 for two 40 mm wide S7-300 modules

•

BM 1 80 for one 80 mm wide S7-300 module

Accessories

•

Explosion-proof partition

•

Backplane bus and bus module cover

… provide the S7-300 backplane bus. In

other words, if a module is missing, all

the other modules can still be reached

via the backplane bus.

Power supply (PS) module
Accessories:

•

Jumper

… converts the mains voltage

(AC 120 / 230 V) to DC 24 V operating

voltage for the supply of the ET 200M.
... can be used as load power supply for

the DC 24 V load circuit.

Summary of Contents for IM 153-4 PN



















































































































































































































































































Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands

Siemens IM 153-4 PN, Operating Instructions Manual

Search results

Summary of Contents for IM 153-4 PN

Reviews:

Brands by name

Popular brands