manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 13

 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

11

 

Product overview 

1

1.1

 

What Are Distributed I/O Devices 

Area of application 

When a system is set up, it is common for the inputs to and outputs from the process to be 

incorporated centrally in the automation system.  
If there are inputs and outputs at considerable distances from the programmable controller, 

there may be long runs of cabling which are not easy to follow, and electromagnetic 

interference may impair reliability. 
Distributed I/O devices are the ideal solution for such systems:  
●

 

the control CPU is located at a central location 

●

 

The I/O devices (inputs and outputs) operate locally on a distributed basis. 

●

 

the powerful PROFIBUS DP with high data transmission speed ensures that the control 

CPU and the I/O devices communicate smoothly. 

●

 

PROFINET IO 

1.2

 

What is PROFIBUS DP? 

What is PROFIBUS DP? 

PROFIBUS DP is an open bus system in accordance with the standard 

IEC 61784-1:2002 Ed1 CP 3/1 with the transmission protocol "DP" (DP is the abbreviation of 

the German term "dezentrale Peripherie" (distributed I/O).  
Physically, the PROFIBUS DP is either an electric network based on a shielded two-wire line 

(RS 485) or an optical network based on a fiber-optic cable (FOC). 
The transmission protocol "DP enables a fast, cyclic data exchange between the control 

CPU and the distributed I/Os. 

What are the DP master and DP slaves? 

The DP master is the connecting link between the control CPU and the distributed I/Os. The 

DP master exchanges the data via the PROFIBUS DP with the distributed I/Os and monitors 

the PROFIBUS DP.  
The distributed I/Os (= DP slaves) prepare the data of the encoder and the actuators on site 

in such a way that they can be transmitted via the PROFIBUS DP to the control CPU.  

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands