manualshive.com logo in svg

Siemens IM 153-4 PN, Operating Instructions Manual

Share
Download
Siemens IM 153-4 PN Operating Instructions Manual Download Page 113

 

Maintenance and service 

 

7.6 Replace modules without the function "Change During Operation" 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

111

 

Removing the Front Connector Coding Key 

Prior to installing the new module, you must remove the front connector coding key from the 

new module. Reason: This part is already available in the wired front connector (refer to the 

following figure). 

 

Figure 7-1 

Removing the Front Connector Coding Key 

Installing a New Module 

Proceed as follows when installing a new module: 
1.

 

Hook the new module of the same type onto the rail and swing it down into place. 

2.

 

Screw the module on securely. 

3.

 

Push the labeling strip of the old module into place on the new module. 

(7

D

E

 

Summary of Contents for IM 153-4 PN



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands