Siemens HB25D5.2 Series, Instruction Manual

Page: 13 / 24

13
2nd rinse
After a short time, the
®
symbol appears again.
Nx ‹
:
„‹
min appears in the display.
1.
Thoroughly rinse out the cleaning sponge.
2.
Remove the remaining water from the evaporator dish using
the cleaning sponge.
3.
Close the appliance door and press the Start button.
The appliance starts rinsing.
Once descaling is complete,
‹‹ : ‹‹ and
®
appear in the
display.
4.
Press the
Ž
button to finish descaling and switch off the
appliance.
Removing the remaining water
Remove the remaining water from the evaporator dish using the
cleaning sponge. Wipe out the cooking compartment using the
cleaning sponge and then dry with a soft cloth.
Cancelling the descaling
Note:
After cancelling the descaling, you must rinse the
appliance twice. The appliance is locked against other
applications until the second rinsing operation is complete.
1.
Press and hold the Stop button to cancel the descaling
process.
To ensure that no descaling solution remains in the
appliance, it must be rinsed twice after a cancellation.
2.
Press the Start button.
The
¯ symbol appears.
Now proceed as described in the “1st rinse“ section.
Troubleshooting
Malfunctions often have simple explanations. Please read the
following instructions before calling the after-sales service.
Repairs may only be carried out by fully trained after-sales
service technicians. Incorrect repairs to your appliance may
present considerable risks for the user.
ã=
Risk of electric shock!
■
Work on the appliance electronics may only be performed by
a specialist.
■
Always disconnect the appliance from the power supply
when work is carried out on the electronics. Switch off the
circuit breaker or remove the fuse from your household fuse
box.
Problem Possible cause Notes/remedy
The appliance does not work The plug is not plugged into the mains Connect the appliance to the electricity
supply
Power cut Check whether other kitchen appliances
are working
Fuse defective Check in the fuse box to make sure that
the fuse for the appliance is OK
Faulty operation Switch the appliance off using the fuse in
the fuse box. Wait approximately
10 seconds and then switch it back on
The appliance cannot be started The appliance door is not fully closed Close the appliance door
Appliance does not start.
Nx
and
‚
:
‹‹
lights up in the display
Descaling has been cancelled Rinse the appliance twice
(see section: Cancelling descaling)
N 0 and ‹‹ : ‹‹ lights up in the display
Power cut Reset the clock
(see section: Changing the clock time)
The appliance is not in operation.
Nx
and
a cooking time lights up in the display
The rotary selector was accidentally oper-
ated
Press the
Ž
button
The Start button was not pressed after
making the setting
Press the Start button to start the appli-
ance, or press the
Ž
button to switch it
off
The
¯
(Fill water tank) indicator appears,
even though the water tank is full
The water tank has not been inserted
properly
Slide in the water tank until it engages
The detection system is not working Descale the appliance (see section: Des-
caling) and check which water hardness
has been set (see section: Setting the
water hardness range)
It is difficult to engage the water tank in
position
Rubber seal on the water tank valve Lightly grease the rubber seal with lubri-
cant (order no. 311 168)
The evaporator dish has boiled empty
even though the water tank is full
The water tank has not been inserted
properly
Slide in the water tank until it engages
The feed line is blocked Descale the appliance (see section: Des-
caling).
Check whether the water hardness range
is set correctly