Siemens Gigaset SX303isdn User Manual Download Page 99

Page: 99 / 183

System settings

SX303/353isdn / englisch / A31008-X353-B100-2-7619 / settings_bs.fm / 14.11.2005

Assigning a phone number (MSN)

You can assign particular individual phone numbers (MSN's) to registered terminals.

When doing this determine

◆

which phone number makes a registered terminal ring (receive MSN),

◆

under which number an internal user dials (send MSN).

Assigning a receive MSN

As supplied, a newly registered handset will ring whenever a phone number you have

set up is dialled.
If you only want to assign the terminal specific receive MSNs:

Assigning a send MSN

You can define one send MSN per internal user. This MSN is shown to the person you

call and the call is also charged to this MSN.

Open the menu.

Set base

Select the menu item and confirm.

Settings

Select the menu item and confirm.

Enter system PIN if required (page 91).

Setup user

Select the menu item and confirm.

Setup device

Select the menu item and confirm.

INT11: Int.11

Select internal number of the terminal and open the

submenu, e.g.

INT11:

Int.11

Receive MSN

Select the menu item and confirm.

Select MSN and confirm, e.g.

MSN1: Anna

(

‰

= set).

Repeat the procedure for further MSNs.

Hold

down (back to idle status).

OK
OK

Open the menu.

Set base

Select the menu item and confirm.

Settings

Select the menu item and confirm.

Enter system PIN if required (page 91).

Setup user

Select the menu item and confirm.

Setup device

Select the menu item and confirm.

INT11: Int.11

Select internal number, e.g.

INT11:

Int.11

Press the display key to open the submenu.

Send MSN

Select the menu item and confirm.

MSN1:

Select MSN and confirm, e.g.

MSN1: Anna

(

‰

= set).

Hold

down (back to idle status).

OK
OK

Summary of Contents for Gigaset SX303isdn
























































































































































































Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands

Siemens Gigaset SX303isdn, User Manual

Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands