Siemens Gigaset SX303isdn User Manual Download Page 140

Page: 140 / 183

137

Operating when connected to a PABX

SX303/353isdn / englisch / A31008-X353-B100-2-7619 / pabx.fm / 14.11.2005

Operating when connected to a PABX

If you are operating your base station on a PABX, special characteristics for receiving text

messages should be noted (page 61).

Access code

Precondition:

If your phone is connected to a PABX you may have to enter an access

code (outside line code) for external calls when first getting started, depending on the

PABX. See the operating instructions for your PABX. You can enter a one to four-digit

access code.
For incoming calls, the access code is automatically placed in front of the caller's phone

number in the display and in the caller lists, and likewise when copied to the

Phonebook. The saved phone number can then be dialled directly, e.g. from the caller

list (page 42).

Activating/deactivating call transfer – ECT (Explicit Call Transfer)

Precondition:

If you want to connect two callers directly with one another (p. 35), then this function

must be activated.
By factory default, this function is deactivated.

Open the menu.

Set base

Select the menu item and confirm.

Settings

Select the menu item and confirm.

Enter system PIN if required (page 91).

System settings

Select the menu item and confirm.

Access code

Select the menu item and confirm.

Enter access code and open the menu.

Save entry

Confirm.

For manual dialling and entering Phonebook, emergency and direct dial

numbers you must also enter the access code.

Open the menu.

Set base

Select the menu item and confirm.

Settings

Select the menu item and confirm.

Enter system PIN if required (page 91).

ISDN settings

Select the menu item and confirm.

Transfer(ECT)

Select the menu item and confirm (

‰

= activated).

If you activate this function, it will automatically be switched to the

Ext. enq. call

(= in the telephone exchange) (page 29).

Summary of Contents for Gigaset SX303isdn
























































































































































































Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands

Siemens Gigaset SX303isdn, User Manual

Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands