Siemens Gigaset SX303isdn User Manual Download Page 135

Page: 135 / 183

132

Operating with other devices

SX303/353isdn / englisch / A31008-X353-B100-2-7619 / devices.fm / 14.11.2005

Setting the device type

Making calls with devices on the analogue connection

(TAE connection)

Telephones with tone dialling (DTMF = dual tone multi-frequency dialling) can be

operated on the analogue connections. Telephones with pulse dialling are not

supported.

Activating/de-activating automatic line seizure

When automatic line seizure is activated, the exchange line is seized as soon as you lift

the receiver. As a result, normal internal dialling is no longer possible.

Open the menu.

Set base

Select the menu item and confirm.

Settings

Select the menu item and confirm.

Enter system PIN if required (page 91).

Setup user

Select the menu item and confirm.

Setup device

Confirm.

INT21: Int.21

Select internal user and open submenu,

e.g.

INT21:

Int.21

Device type

Select the menu item and confirm.

Fax

Select the desired device type and confirm, e.g.

Fax

When changing a setting from a device type for which no receive MSN is

necessary to a device type for which a receive MSN is necessary, all MSNs

programmed in the system are used as active receive MSNs for this

internal user.

Note that only terminals that will be operated in-house (within a building)

may be connected to the analogue TAE connections.

Open the menu.

Set base

Select the menu item and confirm.

Settings

Select the menu item and confirm.

Enter system PIN if required (page 91).

Setup user

Select the menu item and confirm.

Setup device

Select the menu item and confirm.

INT21: Int.21

Select internal user and open submenu,

e.g.

INT21:

Int.21

Auto. seizure

Select the menu item and confirm.

Summary of Contents for Gigaset SX303isdn
























































































































































































Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands

Siemens Gigaset SX303isdn, User Manual

Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands