Siemens Gigaset SX303isdn User Manual Download Page 113 | Manualshive

Page: 113 / 183

background image

110

System settings

SX303/353isdn / englisch / A31008-X353-B100-2-7619 / settings_bs.fm / 14.11.2005

Calling an answering machine in the network (on SX303isdn)

Press

1

and hold

. You are connected directly to the answering machine in the

network. If you then press the handsfree key

d

, you can listen to the answering

machine announcement in the network and operate the answering machine via the

network.

Changing the answering machine number in the network

Viewing/listening to answering machine messages in network

If a message arrives for you, you receive a call from the answering machine in the

network. The number, e.g. 0800 330 2424 for T-NetBox, appears in the display if you

have requested calling line identification. If you accept the call, the new messages are

played back. If you do not accept the call, the number of the answering machine in the

network will be stored in the missed calls list and the message key flashes.

Restoring the factory settings

You can select which type of reset should be performed:

Operational

– All MSNs and access codes (outside line code) are deleted and the AM

(answering machine) PIN (only on Gigaset SX353isdn) is set to 0000. The authorisations

are reset to "Dial and answer".

Reset all

– All functions are reset to their factory defaults. The system PIN is reset to

"0000". All entries (caller list, charges) are deleted.

i

Open the menu.

s

Set base

Select the menu item and confirm.

s

Settings

Select the menu item and confirm.

~

Enter system PIN if required (page 91).

s

System settings

Select the menu item and confirm.

s

Network Mailb.

Select the menu item and confirm.

W

Open the submenu.

s

Change number

Select the menu item and confirm.

~

W

Enter country code and open the menu.

s

Save entry

Select the menu item and confirm.

OK

OK

OK

OK

OK

OK

OK

i

For both functions: Deactivate all active call diversions before resetting!

The terminals remain registered.

i

Open the menu.

s

Set base

Select the menu item and confirm.

s

Settings

Select the menu item and confirm.

OK

OK

«
...
111
112
113
114
115
...
»

Summary of Contents for Gigaset SX303isdn
























































































































































































Reviews:

No comments

Related manuals for Gigaset SX303isdn

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 2

KX-TC1461B - Cordless Telephone

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 23

KX-T7885 - Battery For

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 132

Brand: Panasonic Pages: 12

HYBRID IP-PBX KX-TDA200

Brand: Panasonic Pages: 824

EASA-PHONE KX-T30810

Brand: Panasonic Pages: 16

Brand: Aastra Pages: 28

Brand: HAGENUK Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands