Siemens Gigaset SX303isdn User Manual Download Page 82

Page: 82 / 183

Setting the answering machine (on SX353isdn)

SX303/353isdn / englisch / A31008-X353-B100-2-7619 / answeringm_config.fm / 14.11.2005

Setting the recording time and recording quality

You can set the maximum length of a message and its recording quality. The recording

quality determines the total recording time of your answering machine.
On the

High quality

setting the total recording time is up to 12 min, on

Long

recording

(standard quality, generally adequate) up to 25 min. The

Long recording

recording quality and the

Maximum

recording time are set by factory default.

Setting the recording time

You can limit the maximum length of a message to

1 minute

2 minutes

3 minutes

If you set

Maximum

for the recording time (factory setting) then it is "unlimited" (until

the memory is full).

Precondition:

You have selected an answering machine (page 63).

Setting recording quality

Precondition:

You have selected an answering machine (page 63).

The recording of a call ends:

◆

after a pause in speaking lasting more than 8 seconds;

◆

at the end of a call; the caller terminates the connection;

◆

after the maximum set recording time has elapsed, if the setting

Maximum

was used, when the memory is full.

Settings

Select the menu item and confirm.

Message/Memo

Confirm.

Message length

Confirm.

Maximum

Select the recording time and confirm,

e.g.

Maximum

(

‰

activated).

Hold

down (back to idle status).

When the recording duration is reached, the concluding announcement

is played automatically, if recorded. Then the connection is closed down.

There is no limit to the duration of memo recordings.

Settings

Select the menu item and confirm.

AM quality

Select the menu item and confirm.

either ...

Set high quality:

High quality

Confirm (

‰

activated).

or ...

Set long recording:

Long recording

Select the menu item and confirm (

‰

= activated).

Hold

down (back to idle status).

Summary of Contents for Gigaset SX303isdn
























































































































































































Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands

Siemens Gigaset SX303isdn, User Manual

Search results

Summary of Contents for Gigaset SX303isdn

Reviews:

Related manuals for Gigaset SX303isdn

Brands by name

Popular brands