Siemens Gigaset SX303isdn User Manual Download Page 150 | Manualshive

Page: 150 / 183

background image

147

Appendix

SX303/353isdn / englisch / A31008-X353-B100-2-7619 / appendix.fm / 17.11.2005

Appendix

Care

Wipe the base station and handset with a

damp

cloth (do not use solvent) or an

antistatic cloth.

Never

use a dry cloth. This can cause static.

Contact with liquid

If the handset should come into contact with liquid,

on no account switch the device

on. Remove all batteries immediately.

Allow the liquid to drain out of the device, and then pat all parts of the device dry.
Keep the handset with the batteries removed in a warm, dry place for at least 72 hours.

In many cases, you will then be able to use it again.

Questions and Answers

If you have any questions about the use of your phone, you can contact us 24/7 at

www.siemens.com/gigasetcustomercare

. You will find the most frequently asked

questions and answers below.

!

What has happened

when …

Possible Cause

Possible solution

… the base station does not

ring?

The ringer is switched off.

Internal call diversion is set to 0

ring cycles (= immediate call

diversion).

Night service is active.

Activate (page 114) ringer.

Increase the number of ring

cycles for internal call diversion

Deactivate Night service

… the call units/charges are

not displayed?

There are no metering pulses.

Factor per unit = 0.

Ask your network provider to

transmit the metering pulses.

Set the factor per unit

… the phone number of the

caller

is

not displayed

even

though CLIP is set?

Calling Line Identification is

blocked.

The caller must ask his network

provider to enable the

identification of his number

(CLI).

… the caller list does not

indicate a

time for a

message

?

Date/time are not set.

Set the date/time (page 86).

… the

answering machine

does not record any messages

or has automatically

switched

over

to 'announce only'?

Its memory is full.

Delete old messages

Play back new messages and

delete.

… you can't dial a phone

number any longer?

The long distance prefix has

changed.

Check the long distance prefix

and correct it (page 108).

… there are

no incoming

calls

?

Call diversion

Immediately

is

activated.

The MSN has not been assigned

to the internal user.

The authorisation

Internal only

is set.

Deactivate

Immediately

call

diversion

Determine the receive MSN

Change the authorisation

«
...
148
149
150
151
152
...
»

Summary of Contents for Gigaset SX303isdn
























































































































































































Reviews:

No comments

Related manuals for Gigaset SX303isdn

SP5050 - Bluetooth hands-free Speakerphone

Brand: Jabra Pages: 221

Brand: Jabra Pages: 22

Brand: Jabra Pages: 42

Brand: Panasonic Pages: 76

Brand: Panasonic Pages: 36

Brand: PHOTON Pages: 48

CONVERSip Edge 300

Brand: Vertical Pages: 48

Brand: Uniden Pages: 36

Sailor System 5000 MF/HF

Brand: Sailor Pages: 56

Titan Illuminated Crossing Telephone

Brand: GAI-Tronics Pages: 14

Brand: BELGACOM Pages: 34

Brand: VTech Pages: 40

Brand: Tala Pages: 4

Brand: Kirk Pages: 21

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands