Siemens Gigaset S685 IP Manual Download Page 96

Page: 96 / 278

E-mail messages

Gigaset S675/S685 IP / GBR / A31008-xxxx-xxxx-x-xxxx / email.fm / 5/18/09

ion 8,

.09

.200

Example display:

1 E-mail address or name transmitted by the sender (abbreviated if necessary)

Bold

: New message.

All e-mail messages that were not present in the incoming e-mail server when the

inbox was last opened are identified as "new". All other e-mails are not marked,

regardless of whether or not they have been read.

2 Date and time of receipt of e-mail message

If the inbox on the incoming e-mail server is empty,

No entries

will appear in the

display.

Messages when establishing a connection

The following problems may occur when connecting to the incoming e-mail

server. The messages are displayed in the handset's display for a few seconds.

Server not accessible

The connection to the incoming e-mail server could not be established.

This may have the following causes:
– Incorrect entry for name of incoming e-mail server (

Page 206

– Temporary problems with the incoming e-mail server (server is down or

is not connected to the Internet).

Check settings.

Try again later.

Currently not possible

The resources your phone requires to make the connection are busy, e.g.:
– Two VoIP connections have already been made.

Try again later.

Please note

Many e-mail providers operate standard spam protection measures. E-mail

messages classified as spam are stored in a separate folder and are therefore

not shown in the inbox.
Some e-mail providers allow you to deactivate spam protection or show spam

e-mails in the inbox.
Other e-mail providers may send a message to the inbox when a new spam

e-mail is received. This is to inform you that a suspected spam e-mail has been

received.
Date and sender of this mail are repeatedly updated, so that it is always dis-

played as a new message.

Inbox

Susi Sorglos
15.12.08

12:20

Louise Miller

14.12.08

11:15

Anna Sand

14.12.08

10:45

View

Delete

Summary of Contents for Gigaset S685 IP























































































































































































































































































Search results

Summary of Contents for Gigaset S685 IP

Reviews:

Related manuals for Gigaset S685 IP

Brands by name

Popular brands

Siemens Gigaset S685 IP, Manual

Search results

Summary of Contents for Gigaset S685 IP

Reviews:

Related manuals for Gigaset S685 IP

Brands by name

Popular brands