Siemens Gigaset S670 User Manual Download

Page: 61 / 78

Appendix

Gigaset S670/S675 / IM-MEA En / A31008-M1904-A601-1-3T19 / appendix.fm / 13.8.07

ion 4,

.09.

2005

Appendix

Care

Wipe the base station, charging cradle

and the handset with a

damp

cloth (do

not use solvent) or an antistatic cloth.

Never

use a dry cloth. This can cause a

build up of static.

Contact with liquid

If the handset has come into contact with

liquid:
1.

Turn off the handset and remove the

batteries immediately

2. Allow the liquid to drain from the hand-

set.

3. Pat all parts dry, then place the handset

with the battery compartment open

and the keypad facing down in a dry,

warm place

for at least 72 hours

(

not

in a microwave, oven etc.).

4. Do not turn on the handset again un-

til it is completely dry.

When it has fully dried out, you will nor-

mally be able to use it again.

Questions and answers

If you have any questions about using

your phone, visit us at

www.siemens.com/gigasetcustomercare

at any time. The table below contains a list

of common problems and possible solu-

tions.

The display is blank.

1. The handset is not turned on.

Press

and hold

the end call key

2. The battery is almost flat.

Charge or replace the batteries (page 8).

The keys of a handset do not respond when

pressed.

The keypad lock is activated.

Press and

hold

the hash key

(page 11).

"Base station x" flashes on the display.

1. The handset is outside the range of the base

station.

Move the handset closer to the base sta-

tion.

2. The base station's range is reduced because

eco mode is activated.

Deactivate eco mode (page 13) or

reduce the distance between the hand-

set and the base station.

3. The handset has been deregistered.

4. The base station is not turned on.

Check the base station's mains adapter

(page 8).

Base Search flashes in the display.

The handset is set to

Best Base

and no base sta-

tion is turned on or within range.

Move the handset closer to the base station.

Check the base station's mains adapter

(page 8).

Handset does not ring.

1. The ringer tone is deactivated.

Activate the ringer tone (page 50).

2. Call diversion set to

All Calls

Deactivate call diversion.

Summary of Contents for Gigaset S670















































































Search results

Summary of Contents for Gigaset S670

Reviews:

Related manuals for Gigaset S670

Brands by name

Popular brands

Siemens Gigaset S670, User Manual

Search results

Summary of Contents for Gigaset S670

Reviews:

Related manuals for Gigaset S670

Brands by name

Popular brands