Siemens Gigaset A580 User Manual Download Page 177

Page: 177 / 197

176

Glossary

Gigaset A580 IP / US English / A31008-xxxx-xxxx-x-xxxx / glossary.fm / 28.04.2009

ion 8,

.09

.200

Full duplex

Data transmission is a mode in which data can be sent and received at the same

time.

G.711 a law, G.711 µ law

Standard for a

Codec

G.711 delivers a very good voice quality that corresponds to that in the ISDN

fixed line. As there is little compression, the necessary bandwidth is around 64

kbit/s per voice connection, but the delay caused by coding/decoding is only

0.125 ms.
"a law" describes the European standard and "µ law" describes the North Amer-

ican/Japanese equivalent.

G.722

Standard for a

Codec

G.722 is a

broadband

language codec with a bandwidth of 50 Hz to 7 kHz, a

net transmission rate of 64 kbit/s per language connection and integrated

speech pause recognition and comfort noise generation (silence suppression).
G.722 delivers very good voice quality. A higher sampling rate provides clearer

and better voice quality than other codecs and enables a speech tone in High

Definition Sound Performance (HDSP).

G.726

Standard for a

Codec

G.726 delivers a good voice quality. It is inferior to the quality with codec

G.711

but better than with

G.729

G.729A/B

Standard for a

Codec

The voice quality is more likely to be lower with G.729A/B. As a result of the

high level of compression, the necessary bandwidth is only around 8 kbit/s per

voice connection, but the delay is around 15 ms.

Gateway

Connects two different

Networks

, e.g. a router as an Internet gateway.

For phone calls from

VoIP

to the telephone network, a gateway has to be con-

nected to the IP network and the telephone network (gateway/VoIP provider).

It forwards calls from VoIP to the telephone network as required.

Gateway provider

SIP provider

Global IP address

IP address

GSM

Global System for Mobile Communication

Originally, a European standard for mobile networks. GSM can now be

described as a worldwide standard. In the USA and Japan national standards

are now more frequently supported than in the past.

Summary of Contents for Gigaset A580






































































































































































































Search results

Summary of Contents for Gigaset A580

Reviews:

Brands by name

Popular brands

Siemens Gigaset A580, User Manual

Search results

Summary of Contents for Gigaset A580

Reviews:

Brands by name

Popular brands