Siemens Gigaset A580 IP Manual Download Page 82

Page: 82 / 212

ECO DECT: Reducing the power consumption and transmission power of the base station

Gigaset A580 IP / GBR / A31008-xxxx-xxxx-x-xxxx / T-NetBox_SAG-registration.fm / 24.03.2010

rsion 8, 03.0

.2008

ECO DECT: Reducing the power consumption and
transmission power of the base station

The base station of your phone is an ECO DECT base station, this means that:

The base station and the charging cradle use less power because they are
equipped with a power-saving mains adaptor.

The reduction of the handset's transmission power is dependent on the hand-
set's proximity to the base station.

The base station can also be switched to

Eco mode

Eco mode reduces the transmission power and the power consumption of the
base station further.

Eco mode

means:

80% reduction of the transmission power in standby operation and when mak-
ing calls.

Eco mode

is available when the handset(s) and the base station are

close together, e.g. when the phone is being used in an office.

The setting can be made on the handset.

Activating/deactivating Eco mode

§Menu§

Settings

Base

Additional Features

Eco mode

Select and press

§OK§

(

‰

= on).

Signal displays

Screen icon

Signal strength:

Ð i Ñ Ò

(flashes)

– good to poor
– no signal

Please note

Activating

Eco mode

reduces the range of the base station.

Eco mode

and repeater support (

Page 100

) cancel each other out, i.e. both

functions cannot be used at the same time.

Summary of Contents for Gigaset A580 IP





















































































































































































































Search results

Summary of Contents for Gigaset A580 IP

Reviews:

Related manuals for Gigaset A580 IP

Brands by name

Popular brands

Siemens Gigaset A580 IP, Manual

Search results

Summary of Contents for Gigaset A580 IP

Reviews:

Related manuals for Gigaset A580 IP

Brands by name

Popular brands