Siemens FDUL221 Technical Manual Download Page 50

Page: 50 / 76

Operation
Configuring the line tester

50
Building Technologies

008250_i_en_--

Fire Safety

2013-08-15

6.5

Configuring the line tester

The FDUL221 line tester must be set to the relevant protocol if it is being used on a

detector line. The protocol is permanently set in the 'EL' operation mode and

cannot be configured.

Control panel

Protocol

Mode: FDnet

FC20xx

FDnet

32 V

FC72x

C-NET

32 V

CS114x

FDnet

32 V

SIGMASYS

FDnet

SIGMA

FDnet/C-NET

Spy

To configure, proceed as follows:

The FDUL221 line tester is switched off.

1. Hold down the button and switch the FDUL221 line tester on with the

switch.

The FDUL221 line tester is in the 'Configuration' menu tree.

2. Select 'Mode: FDnet …' using the

buttons.

3. Select the required protocol with the button.
4. Select further sub menus or a function with the

buttons.

5. Further changes in the sub menu or function can be made in the same way.

6. To quit a sub menu or a function, press the button.

7. To quit 'Configuration', select 'Save & Exit' or 'Exit'.

The FDUL221 line tester switches to the 'Topology' menu tree.

Summary of Contents for FDUL221













































































Search results

Summary of Contents for FDUL221

Reviews:

Siemens FDUL221, Technical Manual, Page: 50 / 76

Search results

Summary of Contents for FDUL221

Reviews: