Siemens FDUL221 Technical Manual Download Page 49

Page: 49 / 76

Operation

Switching the line tester on / off

Building Technologies

008250_i_en_--

Fire Safety

2013-08-15

6.4

Switching the line tester on / off

Move the

switch into position <I>.

The 'Topology' menu is opened.
The display briefly indicates the firmware version of the FDUL221 line tester

and 'FDnet …'.

Display for 'EL' operation mode

Then the device designation is displayed with operation mode and the selection

fields.

Display for 'EL' operation mode

The FDUL221 line tester is ready for operation.

Switching on for configuration

To open the 'Configuration' menu tree press the button and switch the

switch to the <I> position at the same time.

The 'Configuration' menu is opened.
The indicator in the display changes to the 'Startup Line' menu.

The FDUL221 line tester is in the ’Configuration’ menu.

Switching off

Move the

switch into position <O>.

The indicator goes out.
If working with the FDUL221-B power unit, the power unit can be removed.

Summary of Contents for FDUL221













































































Search results

Summary of Contents for FDUL221

Reviews:

Siemens FDUL221, Technical Manual, Page: 49 / 76

Search results

Summary of Contents for FDUL221

Reviews: