Siemens FDCW221 Technical Manual Download Page 14

Page: 14 / 52

Setup

Building Technologies

009865_b_en_--.doc

Fire Safety & Security Systems

11.2007

4.5 Accessories

The following accessories for the radio gateway FDCW221 are available:

Details for ordering

Application

9V lithium
battery

A5Q00004142

9V lithium battery

Support battery

DBZ1190-AA 4677080001

Micro

terminal

0.28 … 0.5 mm

If more than one wire
must be connected to the
p.c.b. for each spring clip,
e.g. cable shield from ext.
alarm indicator.

DBZ1190-AB 4942340001

Connection

terminal

1 … 2.5 mm

If more than one wire
must be connected to the
p.c.b. for each spring clip,
e.g. cable shield from ext.
alarm indicator.

DZW1171

5762200001

Radio test set

For the measurement of
the field strength in
buildings.

FDUZ221

A5Q00020131

MCL-USB adapter

Interface converter for
firmware updates on PC.

RadioSpy S24218-F65-A1

Sigmaspace
RadioSpy

To observe, monitor or
configure a radio cell.

The following accessories are available for the radio smoke detector DOW1171:

Details for ordering

Application

9V lithium
battery

A5Q00004142

9V lithium battery

2 batteries are required
for the power supply of
the DOW1171.

The following accessories are available for the manual call point with radio base
SMF6120:

Details for ordering

Application

3.6V lithium
Mignon
battery

V24069-Z112-A1 3.6V lithium Mignon

battery with line and
connector

2 batteries are required
for the power supply of
the SMF6120.

Summary of Contents for FDCW221





















































Search results

Summary of Contents for FDCW221

Reviews:

Related manuals for FDCW221

Brands by name

Popular brands

Siemens FDCW221, Technical Manual

Search results

Summary of Contents for FDCW221

Reviews:

Related manuals for FDCW221

Brands by name

Popular brands