Siemens FDA221 Technical Manual Download

Page: 51 / 114

Mounting / Installation

Preparatory work

Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

5.1.4

Removing and installing the housing cover when the power

supply is switched on

NOTICE

Electrostatic discharge
Damage to electronic components in the aspirating smoke detector

●

When working on the open aspirating smoke detector, use anti-static floor

mats and anti-static work surfaces.

●

Ground yourself immediately before opening the housing, e.g. by touching a

ground point or wearing an anti-static belt.

NOTICE

Accidental triggering of an alarm
Triggering a false alarm

●

When the housing cover is opened, the buzzer sounds. The relay outputs

remain active and the 4…20 mA analog output has been switched to fault

(0.5 mA).

●

If the

button is pressed, the buzzer switches off and the relay

outputs are deactivated. The 4…20 mA analog output remains on fault.

●

Closing the housing cover automatically reactivates the relay outputs and the

4…20 mA analog output switches to normal operation.

When the housing cover is removed, you have access to:



The fixing screws



The cable entry



All the mechanical components



The electrical connections



The rear of the front indicator

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands