Siemens FDA221 Technical Manual Download

Page: 28 / 114

Structure and function
Setup

28
Building Technologies

A6V10334410_h_en_--

Fire Safety

2015-09-29

3.2.2

Internal indicator

When the

housing cover [➙

]

is open, the internal indicator is accessible. The

internal indicator performs the following functions:



Status display for airflow, smoke value, and alarm using 3 LEDs



Activate or stop normalization of the airflow using a button



Activate or stop normalization of the smoke value using a button



Reset self-retaining status displays and relay outputs using a button

Internal indicator

Indication

Designation

Function

Flow ok

The green LED flashes when the airflow is normal.

Smoke ok

The green LED flashes when the smoke value is low.

Alarm

The red LED flashes during an alarm.

Button

Designation

Function

Normalize Flow

Button for activating or stopping normalization of the

airflow.

Normalize Smoke Button for activating or stopping normalization of the

smoke value.

Reset

Button for resetting the self-retaining status displays

and relay outputs. The current detector status is

reset.

The 'Normalize Flow' and 'Normalize Smoke' buttons can only be actuated using

a suitable, thin tool, e.g. a pen or a paper clip.

Summary of Contents for FDA221



















































































































Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands

Siemens FDA221, Technical Manual

Search results

Summary of Contents for FDA221

Reviews:

Related manuals for FDA221

Brands by name

Popular brands