manualshive.com logo in svg

Siemens FCT010/DSL, Operating Instructions Manual, Page: 99 / 180

Share
Download
Siemens FCT010/DSL Operating Instructions Manual Download Page 99

Alarm group 2 (Modbus adddress 3014)

Bit

Diagnostic

Action

0

Frame temp. below limit

Increase fluid temperature and check that ambient temperature is within speci‐
fied limits. If the failure continues then contact Siemens customer support

1

Frame temp. above limit

Reduce fluid temperature and check that ambient temperature is within speci‐
fied limits. If the failure continues then contact Siemens customer support

2

Standard Deviation above limit

(shown for only 2 seconds)

Measurement continues with values from last successful zero point adjust‐
ment. Improve conditions for automatic zero point adjustment and repeat ad‐
justment. 

3

Zero Point Offset above limit

(shown for only 2 seconds)

Measurement continues with values from last successful zero point adjust‐
ment. Improve conditions for automatic zero point adjustment and repeat ad‐
justment. 

4

Zero point adjustment failed

(shown for only 2 seconds)

Measurement continues with values from last successful zero point adjust‐
ment. Improve conditions for automatic zero point adjustment and repeat ad‐
justment. 

5

Empty Tube Limit exceeded

Make sure that the sensor is filled with liquid and that the liquid density is within 
the specified Empty Tube Limit

6

The sensor is partially filled

Make sure that the sensor is filled with liquid 

7

Parameter storage malfunction

Turn off the power, wait 5 seconds and turn on the power again. If the failure 
continues then contact Siemens customer support

8
9
10
11
12
13

Internal error in sensor

Contact Siemens customer support

14

Unstable measurement condition Check if air is present in the liquid and that the flowmeter is operated within its 

specifications

15

Auto filtering

Check that the flowmeter is operated within its specifications. Check other 
alarms to rule out HW malfunction

23

The sensor is stabilizing

Turn off the power, wait 5 seconds and turn on the power again. If the failure 
continues then contact Siemens customer support.

10.3

Operation troubleshooting

10.3.1

Updating the firmware

Note
Firmware update

FW update is to be done only by authorized and trained service personnel.

Diagnostics and troubleshooting FCT010

10.3 Operation troubleshooting

SITRANS MASS 2100 & FC300 (FCT010/DSL)
Operating Instructions, 06/2020, A5E39788682-AB

99

Summary of Contents for FCT010/DSL





















































































































































































Reviews:

No comments