Siemens FCT010/DSL Operating Instructions Manual Download Page 87

Page: 87 / 180

9.3

Cleaning

Cleaning the enclosure

• Clean the outside of the enclosure with the inscriptions using a cloth moistened with water

or a mild detergent.

• Do not use any aggressive cleansing agents or solvents, e.g. acetone. Plastic parts or the

painted surface could be damaged. The inscriptions could become unreadable.

9.3.1

Electrostatic charge

WARNING

Electrostatic charge

Risk of explosion in hazardous areas if electrostatic charges develop, for example, when
cleaning plastic surfaces with a dry cloth.
• Prevent electrostatic charging in hazardous areas.

9.4

Maintenance and repair work

WARNING

Impermissible repair of explosion protected devices

Risk of explosion in hazardous areas
• Repair must be carried out by Siemens authorized personnel only.

WARNING

Maintenance during continued operation in a hazardous area

There is a risk of explosion when carrying out repairs and maintenance on the device in a
hazardous area.
• Isolate the device from power.

- or -
• Ensure that the atmosphere is explosion-free (hot work permit).

Service and maintenance

9.4 Maintenance and repair work

SITRANS MASS 2100 & FC300 (FCT010/DSL)
Operating Instructions, 06/2020, A5E39788682-AB

Summary of Contents for FCT010/DSL





















































































































































































Search results

Summary of Contents for FCT010/DSL

Reviews:

Siemens FCT010/DSL, Operating Instructions Manual, Page: 87 / 180

Search results

Summary of Contents for FCT010/DSL

Reviews: