Siemens FCT010/DSL Operating Instructions Manual Download Page 80 | Manualshive

Page: 80 / 180

Siemens FCT010/DSL Operating Instructions Manual Download Page 80

8.1.5

Process noise damping

Noise damping function

The dynamic sensitivity of the flow measurement signal to rapid changes in process flows can
be reduced by use of the process noise damping function. The function is typically used in
environment with:

• Strongly pulsating flow

• Changing pump speeds

• Large pressure variations

Process noise damping settings

Reduce interfering process noise by increasing the setting of the parameter Process noise
damping (Modbus address 2130).

• Centrifugal pump (1: low)

• Triplex pump (2)

• Duplex pump (3)

• Simplex pump (4)

• Cam pump (5: high)

The default value is Duplex pump. The damping affects all functions and outputs of the sensor.

Centrifugal pump
(1, low)

Triplex pump (2)

Duplex pump
(3, default setting)

Simplex pump (4)

Cam pump (5,
high)

Note
Increased reaction time

The reaction time of the sensor increases when the process noise is damped.

Parameter assignment FCT010
8.1 Functions

SITRANS MASS 2100 & FC300 (FCT010/DSL)

80

Operating Instructions, 06/2020, A5E39788682-AB

«
...
78
79
80
81
82
...
»

Summary of Contents for FCT010/DSL





















































































































































































Reviews:

No comments