manualshive.com logo in svg

Siemens FCT010/DSL, Operating Instructions Manual, Page: 32 / 180

Share
Download
Siemens FCT010/DSL Operating Instructions Manual Download Page 32

4.2.2.2

Orientation of the sensor 

Flow direction 

The calibrated flow direction is indicated by the arrow on the sensor. Flow in this direction will 
be indicated as positive by default. The sensitivity and the accuracy of the sensor do not change 
with reverse flow. 

The indicated flow direction (positive/negative) is configurable.

CAUTION

Accurate measurement

The sensor must always be completely filled with process media in order to measure accurately. 

Orienting the sensor  

The sensor operates in any orientation. The optimal orientation depends on the process fluid 
and the process conditions. Siemens recommends orienting the sensor in one of the following 
ways: 

4.2.2.3

MASS 2100 DI 1.0 - 2.1

Liquid applications

Horizontal installation, correct

Horizontal installation, correct

Vertical installation, correct (liquids without solid 
particles only)

Vertical installation, wrong

Installing/mounting
4.2 Installation instructions

SITRANS MASS 2100 & FC300 (FCT010/DSL)

32

Operating Instructions, 06/2020, A5E39788682-AB

Summary of Contents for FCT010/DSL





















































































































































































Reviews:

No comments